Viewsonic PJ750 Manuale Utente

User GuideGuide de l’utilisateurBedlenungsanleltungGuía del usuarioGuida Dell’utenteAnvändarhandbokKäyttöopas使用者指南使用者指南使用者指南使用者指南使用者指南使用者指南使用者指南使用者指南P

8 ViewSonic PJ750Power ConnectionBe sure to use the correct supplied power cords depending on the power outlet to be connected. Con-nect the AC inlet

ViewSonic PJ750 9OPERATIONSPower ON1Check if the power cord is connected correctly.2Set the power switch to [I]. When the standby mode is selected, t

10 ViewSonic PJ750Basic OperationThe basic operations shown in Table 3 can be performed with the supplied remote control device or by way of the proj

ViewSonic PJ750 11Items indicated by (*) may be used with the control panel.Table 3: Basic Operation (continued)Item DescriptionVOLUMEVolume Adjustm

12 ViewSonic PJ750Setup MenuThe following adjustments and settings are possible when SETUP is selected at the top of the menu. Part of the Setup menu

ViewSonic PJ750 13Input MenuThe following functions are available when INPUT is selected on the menu. Select an item with the and buttons,

14 ViewSonic PJ750Image MenuThe following adjustments and settings are available when IMAGE is selected on the menu. Select an item with the and

ViewSonic PJ750 15Options MenuThe following adjustments and settings are available when OPT. is selected on the menu. Select an item with the a

16 ViewSonic PJ750No Signal MenuThe same adjustments and settings are available as with the Image and Options menus when the MENU button is pressed d

ViewSonic PJ750 17MAINTENANCELampContact your dealer before replacing the lamp.See the item “Optional Parts” in Table 12.Before replacing the lamp, s

ViewSonic PJ750 iContentsFor Your Records ... 1FEATURESBEFO

18 ViewSonic PJ750Replacing the Lamp1Switch the projector OFF, remove the power cord from the power outlet, and wait at least 45 minutes for the unit

ViewSonic PJ750 19Air FiltersCleaning Air FiltersThe air filter should be cleaned as described below at an interval of approximately 300 hours.1Switc

20 ViewSonic PJ750TROUBLESHOOTINGOSD MessageThe messages as described below may appear on the screen at power ON. Take the appropriate mea-sures when

ViewSonic PJ750 21Indicator MessageThe POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the appropriate measure

22 ViewSonic PJ750SymptomBefore requesting repair, please check in the following chart. If the situation cannot be corrected, then contact your deale

ViewSonic PJ750 23SPECIFICATIONSTable 12: SpecificationsNOTE: • These specifications are subject to change without notice.Item SpecificationLiquid c

24 ViewSonic PJ750Customer SupportFor technical support or product service, see the table below or contact your reseller.NOTE: You will need the prod

ViewSonic PJ750 25LIMITED WARRANTYVIEWSONIC ProjectorWhat the warranty covers:ViewSonic® warrants its products to be free from defects in material

26 ViewSonic PJ750AppendixPower Cord Safety GuidelinesCaution: Use a power cable that is properly grounded. Always use an AC power cord that meets yo

ViewSonic PJ750 27FCC InformationThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15

ViewSonic PJ750 1Copyright © ViewSonic Corporation, 2002. All rights reserved. Macintosh, Mac and Power Macintosh are registered trademarks of Apple

ViewSonic Corporation

2 ViewSonic PJ750FEATURESThis liquid crystal projector is used to project various computer signals as well as NTSC/PAL/SECAM video signals onto a scr

ViewSonic PJ750 3Part Names

4 ViewSonic PJ750 These functions work when the function for controlling the mouse has been activated. The mouse-controlling function will be dis

ViewSonic PJ750 5Inserting the BatteriesInsert the AA batteries into the remote control device.1Remove the battery cover.Push the knob while lifting

6 ViewSonic PJ750INSTALLATIONInstallation of the Projector and ScreenTo set the screen size and projection distance, see the illustration and table b

ViewSonic PJ750 7CablingRefer to the table below for connecting each terminal of the projector to each device.Table 2: CablingCAUTION• An incorrect