ViewSonic PJD6210-WH Guida Utente

DLP ProjectorPJD6210PJD6210-WHPJD6210-3DViewSonic®IMPORTANT: Please read this User Guide to obtain important information on install-ing and using you

Projector OverviewFront ViewCaution Do not touch the lamp cover and exhaust vents during projector usage to prevent from possible burning. Do not lo

Rear View Security lockKensington lockAC power socketConnection ports Ventilation holes (exhaust)Bottom ViewCeiling mountTilt-adjustment feet 45 32112

Using the ProductControl PanelLEDButton FunctionLamp (Lamp LED indicator)Refer to “LED Indicator Messages”.Temp (Temperature LED indicator)Refer to “L

Connection PortsRS232Reserved for installation control and firmware upgrades. COMPUTER INConnect image input signal (analog RGB or component) to this

Remote ControlPOWERTurn the projector on or off.Four directional buttonsUse four directional buttons toselect items or make adjustmentsto your selecti

Replacing the BatteryFor the first time use:Remove the transparent insulation tape by pullingit before use.For battery change:1. Push the catch to the

Remote Control OperationPoint the remote control at the infrared remote sensor and press a button. Operating the projector fromthe front30207m10 The

InstallationConnecting the ProjectorRS-232 Cable VGA (D-Sub) to HDTV (RCA) CableVGA Cable (D-Sub to D-Sub) Composite Video Cable1 32 4Desktop typeLapt

Powering On/Off the ProjectorPowering On the Projector:1. Remove the projector lens cap.2. Complete the AC power cord and peripheral signal cable(s) c

Adjusting the ProjectorAdjusting the Projector HeightThe projector is equipped with two tilt-adjustment feet to adjust the image height.To level the i

Notes on the AC Power CordAC Power Cord must meet the requirement of countries where you use this projector.Please confirm your AC plug type with the

Adjusting Projection Image SizeRefer to the graphic and table below to determine the screen size and projection distance.Screen SizeDiagonal (Inch)4 :

Menu OperationThe projector has multilingual on-screen display menus that allow you to make imageadjustments and change a variety of settings.*1 Adjus

PJD6210-3D FunctionThe projector has different menu and compatibility modes for 3D function as below.Menu * 1 Adjustable range and default setting

How to operate1. Press the MENU button to open the OSD menu.2. When OSD is displayed, use S / T to select any feature in the main menu.3.After selecti

GammaEffect the represent of dark scenery. With greater gamma value, dark scenery will look brighter.Computer Image (Computer Mode)FrequencyAdjust the

Auto SourceAutomatically scan through all the input source.ECO ModeUse this function to dim the projector lamp light output which will lower powercons

MaintenanceThe projector needs proper maintenance. You should keep the lens clean as dust, dirtor spots will project on the screen and diminish image

Replacing the LampAs the projector operates over time, the brightness of the projector lamp graduallydecreases and the lamp becomes more susceptible t

1. Turn off the projector.2. Unplug the power cord. If the projector is installed in a ceiling mount, remove it from the mount. Place a protective sh

SpecificationsDisplay Type Single 0.55" DLP panelResolution (Pixels) XGA (1024 × 768)Lens Manual Zoom (1.1x)Screen Size 30” – 300”Lamp 180WInput

CONTENTSIntroduction... 5Projector Features...

AppendixLED Indicator MessagesLamp LED Temp LED Power LED MeaningOff Off100% blinking blueStand-by modeOff Off Solid blueThe projector is in good cond

Compatibility ModesComputer: Video: Compatibility Resolution H-Sync [KHz] V-Sync [Hz]VGA 640 x 480 31.5 59.937.9 72.837.5 75.043.3 85.0SVGA 800 x 600

TroubleshootingRefer to the symptoms and measures listed below before sending the projectorforrepairs. If the problem persists, contact your local res

RS-232 Command and ConfigurationBaud Rate:19200 Parity Bit:none Data Bit:8 Stop Bit:1 Assign Port:COM1* RS-232 Cable PN: CB-00008741NameOperation

Mini DIN 8 pinIR Control Code 1 RXD2USB_DN3-4GND5USB_DP6-7TXD8USB+5VButton name Product ID Code Data Code DescriptionPower 0x83 , 0xF4 87 P

Customer SupportFor technical support or product service, see the table below or contact your reseller.Note : You will need the product serial number.

Limited WarrantyVIEWSONIC® PROJECTORWhat the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, und

How to get service: 1. For information about receiving service under warranty, contact ViewSonic Customer Support (please refer to “Customer Suppor

Mexico Limited WarrantyVIEWSONIC® PROJECTORWhat the warranty covers:ViewSonic warrants its products to be free from defects in material and workmanshi

Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:Name, address, of manufacturer and importers:Méxi

ViewSonicPJD6210/PJD6210-WH/PJD6210-3DCompliance InformationFCC StatementThis device complies with part 15 of FCC Rules. Operation is subject to the f

Downloaded From projector-manual.com Viewsonic Manuals

ViewSonicPJD6210/PJD6210-WH/PJD6210-3DImportant Safety Instructions1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follo

ViewSonicPJD6210/PJD6210-WH/PJD6210-3DDeclaration of RoHS ComplianceThis product has been designed and manufactured in compliance with Directive 2002/

ViewSonicPJD6210/PJD6210-WH/PJD6210-3DCopyright InformationCopyright© ViewSonic© Corporation, 2009. All rights reserved.Macintosh and Power Macintosh

IntroductionProjector FeaturesThe projector integrates high-performance optical engine projection and a user - friendlydesign to deliver high reliabil

Package ContentsWhen you unpack the projector, make sure you have all these components:Caution Avoid using the projector in dust environment. Leave